Lasersaur

Share
Embed
Fork this BOM
I'm building this

Copy and paste this code:

Create a project variation named:

 
 
 
Filter vendors by:

Bill of Materials

 
Qty Part Specific Use Recommended Purchase
Frame-outer
1 loctite 248 threadlocking glue for all screws where we cannot use belleville washers or lock nuts
2 screw ISO7380, button, M3x16 door switch
12 screw DIN7991, sunk, M5x08 door hinges
131 screw DIN912, cap, M5x10 28x front, 8x sides, 16x rear, 35x bottom, 16x top, 16x door, 8x middle, 4x door stop
3 screw ISO7380, button, M5x12 door switch
4 screw ISO7380, button, M5x16 gas spring mount
2 washer DIN9021, form G, M3 door switch
16 washer DIN125, form A, M5 gas spring mount
11 washer DIN9021, form G, M5 3x door switch, 8x gas spring
127 washer DIN6797, lock, M5 28x front, 8x sides, 16x rear, 35x bottom, 16x top, 12 door, 8x middle, 4x door stop
2 nut DIN985, nyloc thin, M3 door switch
4 nut DIN985, nyloc thin, M5 gas spring mount
4 tslot 2020, 1690mm long edges
4 tslot 2020, 1040mm short edges
2 tslot 2040, 1040mm short bands
3 tslot 2040, 1040mm, black short bands, bottom
1 tslot 2020, 1240mm top mid bar
1 tslot 2040, 240mm mid beam, top, back
7 tslot 2040, 310mm gantry legs, back columns
2 tslot 2020, 310mm corner column, back
3 tslot 2040, 80mm front column
6 tslot 2040, 150mm column, front, internal, middle
2 tslot 2040, 600mm, black base cross
2 tslot 2020, 1176mm door wide
2 tslot 2020, 725mm door short
1 tslot 2040, 725mm door mid beam
2 tslot 2020, 500mm, black laser power mount
1 tslot 2040, 170mm cable carrier mount
8 corner bracket, 3-way frame corner brackets
4 corner bracket, 2-way door corner brackets
2 plate bracket, double door stop
4 angle bracket, double gas spring mount
54 angle bracket, single 14x front, 4x sides, 8x rear, 14x bottom, 8x top, 2x door, 4x middle
6 angle bracket, single, black base cross, 2x lp mount
3 hinges door
146 tslot nut, pre, M5 135x table frame, 11x door
40 tslot nut, post, M5 for convinience
2 gas spring door
2 platic handles door
1 custom door sensor A sensor to frame mounting plate
1 custom door sensor B interruptor plate
Electronics
12 screw ISO7380, button, M3x16 4x arduino mount, 8x gecko mount
12 washer DIN9021, form G, M3 4x arduino mount, 8x gecko mount
6 washer DIN9021, form G, M5 4x panel mount, 2x din rail mount
12 nut DIN985, nyloc thin, M3 4x arduino mount, 8x gecko mount
2 nut DIN985, nyloc thin, M5 panel mount
2 screw ISO7380, button, M5x20 panel mount
2 GeckoDrive G203V x/y-drive
3 slot cover, yellow cable to frame
1 Arduino Uno stepper control
1 power supply 24V for DIN rail stepper power
1 heat shrink tubing set cable to sensor, stepper, laser
1 screw terminal connectors cable to laser tube
1 e-stop button 24mm e-stop
1 e-stop SPST block e-stop
1 DIN rail 1m electronics mounting
1 relay 277VAC@25A e-stop relay
12 terminal block for DIN rail switch board
3 terminal block side cover switch board
5 terminal block bridge switch board
1 wire, 4 strands, 24awg, shielded, 30m low amp wire
5 opto-interrupter limit switches x/y, door
2 nand logic ICs board logic
1 36 pin header 2.54mm pitch board to arduino, ISP
10 screw terminal, 2.54mm pitch stepper, sensors
2 screw terminal, 3.5mm pitch board to stepper driver
1 screw terminal, 5.08mm pitch power-in
1 resistor 6.5 KOhm x-axis stepper driver
1 resistor 20 KOhm y-axis stepper driver
5 resistor 100 Ohm opto LED (limit to 16mA)
7 resistor 10 KOhm opto pullup resistor
1 power entry module C-14 net power line
1 usb entry module usb panel mount
1 Nema 17 Stepper x-drive
1 NEMA 23 Stepper + rear shaft y-drive
1 LasaurShield v12.02 controller
1 electronics mounting panel controller, stepper driver mount
X-drive
4 screw ISO7380, button, M3x16 limit switches
4 screw ISO7380, button, M5x12 2x pulley, 2x idler
8 washer DIN9021, form G, M3 4x motor, 4x limit switch
4 washer DIN9021, form G, M5 2x pulley, 2x idler
4 nut DIN985, nyloc thin, M3 limit switch
4 tslot nut, pre, M5 idler, motor
4 washer DIN125, form A, M4 belt clamp
7 nut DIN985, nyloc thin, M4 2x bearing, 1x idler shaft, 4x belt clamp
4 screw ISO7380, button, M3x10 motor mount
12 screw ISO7380, button, M4x20 bearing
2 screw ISO7380, button, M4x25 belt clamp, air assist
1 timing belt XL, 600 teeth, 3050mm drive belt
1 timing pulley XL, 12 teeth, bore 4mm idler pulley
1 timing pulley XL, 12 teeth, bore 5mm motor pulley
1 timing belt clamp belt attachment
2 ball bearing 4x13x5mm idler pulley
1 ball bearing sleeve bearing alignment
1 cantilever pin idler shaft
1 custom idler mount A x-drive idler assembly
1 custom idler mount B x-drive idler assembly
1 custom NEMA17 motor mount x-drive motor mount
Y-drive
4 screw ISO7380, button, M3x16 limit switches
2 screw DIN912, cap, M5x10 motor mount
4 screw ISO7380, button, M5x12 motor shaft mount
4 washer DIN9021, form G, M3 limit switch
6 washer DIN125, form A, M5 motor mount
12 washer DIN9021, form G, M5 4x pulley mount, 4x idler mount, 4x limit switch
2 washer DIN6797, lock, M5 motor bracket
4 nut DIN985, nyloc thin, M3 limit switch
6 nut DIN985, nyloc thin, M5 motor mount
14 tslot nut, pre, M5 8x pulley/idler, 2x motor, 4x limit switch
10 nut DIN985, nyloc thin, M4 8x bearing, 2xidler shafts
4 rubber washer cantilever roller bottom
2 timing pulley XL, 12 teeth, bore 4mm idler left/right
4 ball bearing 4x13x5mm idler
2 ball bearing sleeve bearing alignment
2 cantilever pin idler shaft
8 zip tie, 2.5x100mm, black timing belt to carts
14 screw ISO7380, button, M5x20 4x idler mount, 6x motor, 4x limit switch
2 timing belt XL, 350 teeth, 1780mm drive belt left/right
2 timing pulley XL, 12 teeth, bore 6mm pulley left/right, set screw
1 angle bracket, heavy, long, narrow motor mount
2 ball bearing 6x19x6mm pulley shaft
2 rotary shaft with step motor to pulley
2 shaft coupling, 6.35 to 8mm motor to shaft
2 custom pulley mount bearing mount for pulley shaft
4 custom idler mount bearing mount for idler cantilever pin
1 custom NEMA23 motor mount y-drive motor mount
2 custom sensor mount A limit switch assembly
2 custom sensor mount B limit switch assembly
Frame-gantry
32 screw DIN912, cap, M5x10 corner connection
80 washer DIN6797, lock, M5 corner: 16x angle, 64x plate
4 plate bracket, double corner connection
32 tslot nut, pre, M5 corner connection
2 tslot 4040, 860mm, gantry frame gantry frame
2 tslot 4080, 1660mm, gantry frame gantry frame
4 angle bracket, heavy, long corner connection
Frame-table
44 screw DIN912, cap, M5x10 table frame
44 washer DIN6797, lock, M5 table frame
22 angle bracket, single, black table frame
44 tslot nut, pre, M5 table frame
2 tslot 2040, 876mm, black table short
2 tslot 2040, 1280mm, black table wide
7 tslot 2020, 620mm, black table cross
Y-cart
4 screw DIN912, cap, M5x10 cart-bar mount
4 screw ISO7380, button, M5x16 cart-bar mount
8 washer DIN9021, form G, M3 in-plane roller
4 washer DIN9021, form G, M5 cart-bar mount
8 washer DIN6797, lock, M5 cart-bar mount
4 nut DIN985, nyloc thin, M3 in-plane roller
4 nut DIN985, nyloc thin, M5 cart-bar mount
2 angle bracket, double cart-bar mount
4 tslot nut, pre, M5 cart-bar mount
4 screw ISO7380, button, M3x12 in-plane roller
32 washer DIN9021, form G, M4 cantilever roller
12 washer DIN125, form A, M4 cantilever roller
4 washer DIN125, form A, M6 in-plane roller
12 nut DIN985, nyloc thin, M4 cantilever roller
6 ball bearing roller 4x13x5mm cantilever roller
2 ball bearing roller 6x19x6mm cantilever roller
2 roller shaft, 6x20mm in-plane roller
6 screw ISO7380, button, M4x25 cantilever roller
2 screw ISO7380, button, M3x06 cable carrier
4 screw ISO7380, button, M5x25 timing belt attachment
1 tslot 2040, 1550mm cart-bar
3 cable carrier, 10 links, 180mm stepper and sensors
2 cable carrier mount stepper and sensors
2 tslot nut, pre, M3 cable carrier
2 custom roller mount y-cart roller assembly
Optics-laser
16 screw DIN912, cap, M5x10 2x front, 2x rear, 12x laser mount
2 screw ISO7380, button, M5x12 mirror to tslot
2 screw ISO7380, button, M5x16 mirror base, rear
4 washer DIN9021, form G, M3 laser head
12 washer DIN9021, form G, M5 8x mirror plates, 4x laser mount
14 washer DIN6797, lock, M5 2x mirror rear, 12x laser mount
6 nut DIN985, nyloc thin, M5 2x mirror rear, 4x laser mount
16 tslot nut, pre, M5 4x mirror mounts, 12x laser mount
1 angle bracket, heavy, long mirror, rear
8 washer DIN9021, form G, M4 laser mount
2 washer DIN125, form A, M4 mirror mounts
6 nut DIN985, nyloc thin, M4 2x mirror mounts, 4x laser mount
6 screw ISO7380, button, M4x20 2x mirror base, 4x laser mount
2 screw ISO7380, button, M5x25 mirror plate, rear
8 zip tie, 2.5x100mm, black cable and hose to laser tube
8 screw ISO7380, button, M5x20 laser mount
1 laser tube main laser
1 laser power supply (specify 220V or 110V) main laser
1 water chiller (specify 220V or 110V) main laser
4 screw unc/imperial, 4-40, 0.5inch flying optics, head
4 angle bracket, heavy, double laser mount
2 tslot 4040, 60mm laser mount
2 hinge nuts mirror base
1 water hose ID 6mm, 10m chiller to laser to chiller
2 tube coupling + 9mm shoot chiller hose to laser hose
2 sleeve for 6mm shoot chiller hose to laser hose
2 band for 6mm shoot chiller hose
4 band for 9mm shoot chiller hose
1 custom mirror mount A mirror to frame mounting plate
2 custom mirror mount B mirror to frame mounting plate
2 custom laser mount A 60mm laser to frame mounting plate
2 custom laser mount B 60mm laser to frame mounting plate
2 mirror mount flying optics, 1, 2
1 angle mirror mount flying optics, head
1 adjustable pipe flying optics, head
1 2inch pipe flying optics, head
3 silver IR mirror flying optics, 1, 2, head
1 ir lens flying optics, head
1 spanner wrench assembly tool
1 safety glasses for 10600nm for owners eyes
2 6mm shoot chiller hose to laser hose
Air-assist
2 screw DIN912, cap, M5x10 boom hinge
2 washer DIN6797, lock, M5 boom hinge
1 tslot 2040, 240mm cable carrier boom
1 angle bracket, double cart-bar mount
4 tslot nut, pre, M5 boom hinge
2 screw ISO7380, button, M5x08 boom hinge
2 screw ISO7380, button, M3x06 cable carrier
5 cable carrier, 10 links, 180mm frame to head
2 cable carrier mount cable carrier
2 tslot nut, pre, M3 cable carrier and hinge
2 tslot 2040 end cap cable carrier boom
1 hinge cable carrier boom
X-cart
16 washer DIN9021, form G, M3 16x in-plane roller
8 nut DIN985, nyloc thin, M3 8x in-plane roller
8 screw ISO7380, button, M3x12 in-plane roller
9 washer DIN9021, form G, M4 rod roller
9 washer DIN125, form A, M4 rod roller
8 washer DIN125, form A, M6 in-plane roller
12 nut DIN985, nyloc thin, M4 rod roller
3 ball bearing roller 4x13x5mm rod roller
4 ball bearing roller 6x19x6mm in-plane roller
4 rubber washer rear rod roller
3 threaded rod, m4, 60mm rod roller
4 roller shaft, 6x20mm in-plane roller
1 custom head plate A x-cart assembly
1 custom head plate B x-cart assembly
Frame-panels
108 washer DIN6797, lock, M5 panel corners/sides
108 tslot nut, pre, M5 panel corners/sides
108 screw ISO7380, button, M5x08 panel corners/sides
8 low-density foam tape 1/8x1/4"x17ft panel sealing and laser mount
2 polycarbonate sheet 3mm, 4 holes door cover
4 metal sheet 1076x206x0.8mm side top and bottom
2 metal sheet 640x276x0.8mm rear top
4 metal sheet 640x536x0.8mm center cross bottom
4 metal sheet 346x206x0.8mm side front and rear
4 metal sheet 640x346x0.8mm center front and rear
2 metal sheet 1076x346x0.8mm sides
Extra
1 tslot 2020, 1040mm extra
1 tslot 2040, 1040mm extra
4 angle bracket, double extra
4 angle bracket, single extra
40 tslot nut, pre, M5 extra
1 angle bracket, heavy, long extra

Purchase Info

Vendor Name
Vendor Item Name or ID
Vendor Item URL
Price per Item
# to Buy for Entire Project