Copy and paste this code:
Create a project variation named:
| Qty | Part | Specific Use | Recommended Purchase |
|---|---|---|---|
| Wade's Extruder | |||
| 1 | M8 Hex Nylon Lock Nut | Keeps hobbed bolt nut from vibrating loose | |
| 3 | M3 Hex Nut | 1 for gear, 2 to attach extruder to x carriage | |
| 1 | M8 Hex Nut | Secures hobbed bolt, don't over-tighten | |
| 6 | M3 Flat Washer | 4 used to mount motor, 2 to attach extruder to x carriage | |
| 4 | M4 Flat Washer | Used to attach springs to idler mount | |
| 5 | M8 Flat Washer | Used to align groove in hobbed bolt with filament hole in Wade's Body, usually 3 front and 2 back | |
| 4 | M4 Wing Nut | Attaches to M4 x 50mm bolts, adjusts tension of springs for the Wade's idler | |
| 4 | M3 x 10mm Machine Screw | Used to attach motor | |
| 2 | M3 x 40mm Machine Screw | Used to attach extruder to x carriage | |
| 4 | M4 x 50mm Tap Bolt | Attaches Wade's Extruder Body to Wade's Extruder Idler | |
| 1 | M3 x 8mm Set Screw | Attaches Wade's Small Gear to Motor | |
| 3 | 608 Bearing | 1 bearing acts as idler pushing filament into groove on hobbed bolt, 2 allow hobbed bolt to spin | |
| 1 | NEMA-17 Bipolar Stepper Motor | Power filament extrusion | |
| 4 | M4 Spring | Slides over M4 x 50mm bolts, tensions the Wade's Idler | |
| 1 | Wade's Geared Extruder Body | Main body of the Wade's Extruder | |
| 1 | M8 x 60mm Hobbed Bolt | Groove in hobbed bolt drives filament extrusion | |
| 1 | M8 x 20mm Smooth Rod | Idler stud for mounting 608 bearing | |
| 1 | Wade's Geared Extruder Idler | Mounts idler bearing to tension filament | |
| 1 | Wade's Extruder Big Gear | Attaches to, and spins, hobbed bolt | |
| 1 | Wade's Extruder Small Gear | Attaches to motor and turns Wade's Big Gear | |
| X-axis | |||
| 2 | M8 Hex Nylon Lock Nut | Keeps x-axis idler nut from vibrating loose, 1 front, 1 back | |
| 2 | M2 Hex Nut | Secures Mechanical Endstop to Endstop Holder | |
| 14 | M3 Hex Nut | 4 to attach belt to x carriage, 8 to attach x carriage to bushings, 1 for pulley gear, 1 for endstop | |
| 5 | M8 Hex Nut | Secures x end motor mount and x end idler to z-axis threaded rods | |
| 13 | M3 Flat Washer | 4 to attach belt to x carriage, 8 to attach x carriage to bushings, 1 for endstop | |
| 2 | M8 Flat Washer | Used around 608 bearings | |
| 2 | M2 x 20mm Machine Screw | Secures Mechanical Endstop to Endstop Holder | |
| 11 | M3 x 10mm Machine Screw | 8 used to attach x carriage to bushings, 3 to attach motor | |
| 4 | M3 x 20mm Machine Screw | Used to attach belt to x carriage | |
| 1 | M3 x 8mm Set Screw | Secures x-axis pulley to motor | |
| 1 | Prusa Endstop Holder | Mounts x-axis endstop to smooth rod | |
| 1 | Prusa X Carriage | Mount for Wade's Extruder and Hotend, glides on x-axis smooth rods for movement | |
| 1 | Prusa X End Idler | Idler for x-axis drive belt, attaches x-axis smooth rods to z-axis rods | |
| 1 | Prusa X End Motor Mount | Mount for x-axis motor, attaches x-axis smooth rods to z-axis rods | |
| 2 | Prusa Belt Clamp | Attaches x-axis drive belt to x carriage | |
| 1 | Prusa Pulley | Attaches to x-axis motor, drives x-axis belt | |
| 4 | Prusa PLA Bushing | Attaches x carriage to x-axis smooth rods | |
| 2 | M8 x 30mm Fender Washer | Keeps x-axis belt from falling off idler bearing | |
| 1 | 608 Bearing | Idler bearing for x-axis belt | |
| 1 | M8 x 50mm Threaded Rod | Attaches idler bearing and hardware to x end idler | |
| 1 | M5 x 900mm T5 Timing Belt | Drive belt for x-axis movement | |
| 1 | NEMA-17 Bipolar Stepper Motor | Powers x-axis movement via drive belt | |
| 1 | Mechanical Endstop | Detects minimum position of x carriage | |
| 2 | 7/16" x 1" Spring | Anti-kickback springs to protect print bed and hotend, 1 for x end idler, 1 for x end motor mount | |
| 2 | M8 x 430mm Smooth Rod | ||
| Y-axis | |||
| 4 | M8 Hex Nylon Lock Nut | Used to secure the fender washers against the 608 bearing while allowing them to spin | |
| 2 | M2 Hex Nut | Secures Mechanical Endstop to Endstop Holder | |
| 15 | M3 Hex Nut | 4 to attach print bed to bushings, 8 to attach heated bed and springs to bed, 1 for belt pulley, 6 to attach print bed to bushings | |
| 14 | M3 Flat Washer | 3 to mount motor, 6 to attach print bed to bushings, 4 to attach belt to bed, 1 for endstop, 12 to attach heated bed & springs to bed | |
| 2 | M2 x 20mm Machine Screw | Secures Mechanical Endstop to Endstop Holder | |
| 3 | M3 x 10mm Machine Screw | To attach motor | |
| 6 | M3 x 20mm Machine Screw | To attach print bed to bushings | |
| 4 | M3 x 25mm Machine Screw | To attach belt to aluminum sheet for print bed | |
| 1 | M3 x 8mm Set Screw | Secures y-axis pulley to motor | |
| 1 | Prusa Endstop Holder | Mounts y-axis endstop to smooth rod | |
| 1 | Prusa Y Motor Bracket | Attaches y-axis motor to frame, lower front | |
| 2 | Prusa Belt Clamp | Attaches y-axis drive belt to print bed | |
| 4 | Prusa Bar Clamp | Attaches y-axis smooth rods to frame, 2 lower front, 2 lower back | |
| 1 | Prusa Pulley | Attaches to y-axis motor, drives y-axis belt | |
| 3 | Prusa PLA Bushing | Attaches print bed to y-axis smooth rods, allows for bed movement | |
| 2 | M8 x 406mm Smooth Rod | Y-axis glides on these rods | |
| 1 | M4 250mm x 250mm Print Bed | Moving y-axis print surface, attachment point for belt ends | |
| 1 | M5 x 840mm T5 Timing Belt | Drive belt for y-axis movement | |
| 1 | NEMA-17 Bipolar Stepper Motor | Powers y-axis movement via drive belt | |
| 1 | Mechanical Endstop | Detects minimum position of print bed | |
| Z-axis | |||
| 2 | M2 Hex Nut | Secures Mechanical Endstop to Endstop Holder | |
| 11 | M3 Hex Nut | 4 to attach motor couplers, 2 to tighten motor couplers, 1 for endstop, 4 to attach clamp to z axis smooth rod | |
| 8 | M8 Hex Nut | To attach motor mounts | |
| 17 | M3 Flat Washer | 4 to attach clamp to z axis smooth rod, 1 for endstop, 4 to attach motor couplers, 8 to attach motors | |
| 12 | M8 Flat Washer | 8 to attach motor mounts, 4 to attach z axis smooth rods | |
| 2 | M2 x 20mm Machine Screw | Secures Mechanical Endstop to Endstop Holder | |
| 10 | M3 x 10mm Machine Screw | 8 to attach motors, 2 to tighten on couplers | |
| 5 | M3 x 20mm Machine Screw | 4 to attach motor couplers, 1 for endstop | |
| 4 | M3 x 25mm Tap Bolt | To attach clamp to z axis smooth rod to motor moutn | |
| 2 | Prusa Coupling | Attaches z-axis motors to z-axis threaded drive rods | |
| 1 | Prusa Endstop Holder | Mounts z-axis endstop to smooth rod | |
| 2 | Prusa Z Motor Mount | Mounts z-axis motors to frame, 1 top left, 1 top right | |
| 2 | Prusa Bar Clamp | Attaches z-axis smooth rods to frame lower middle threaded rod | |
| 2 | Prusa Rod Clamp | Attaches z-axis smooth rods to z motor mounts | |
| 2 | M8 x 210mm Threaded Rod | Drive rods for z-axis movement | |
| 2 | M8 x 350mm Smooth Rod | Allows x end idler and x end motor mount to slide along z-axis | |
| 2 | NEMA-17 Bipolar Stepper Motor | Powers z-axis movement via drive rods | |
| 1 | Mechanical Endstop | Detects minimum position of z-axis, used to position hotend above print bed | |
| Electronics | |||
| 2 | M3 Hex Nut | Used to attach electronics mount to threaded rod | |
| 2 | M3 Flat Washer | Used to attach electronics mount to threaded rod | |
| 5 | M3 x 20mm Machine Screw | 2 used to attach electronics mounted to threaded rod, 3 used to clamp ramps and arduino | |
| 1 | Arduino Mega 2560 R3 | Brains of the Prusa, Marlin firmware recommended | |
| 1 | Ramps | All-in-one reprap arduino shield to connect motors, heated elements and sensors | |
| 1 | RAMPs Mounting Bracket | Attaches Arduino and RAMPs to the Prusa frame | |
| 4 | Pololu RAMPs Stepper Driver | Stepper motor driver, attaches to RAMPs board | |
| Heated Bed | |||
| 4 | M3 Hex Nut | Attaches heated bed to print bed | |
| 12 | M3 Flat Washer | Attaches heated bed to print bed | |
| 4 | M3 x 40mm Machine Screw | Attaches heated bed to print bed | |
| 1 | Prusa Heated Bed | Heated print surface to improve adhesion and prevent warping | |
| 4 | M4 Spring | Mounts on M3 x 40mm screws to level heated bed above print bed | |
| 1 | Heat Bed Cover | Borosilicate glass is rated for higher temperatures than normal sheet glass making it a better material for use as a heated bed. | |
| 1 | Binder Clips | Used to hold Glass Heat Bed Cover on heated print bed | |
| Frame | |||
| 67 | M8 Hex Nut | 8 per corner, 4 used for threaded cross bar that attaches to z axis bars, 8 to attach y axis smooth rods, 7 to attach motor and pulleys | |
| 68 | M8 Flat Washer | 8 per corner, 4 used for threaded cross bar that attaches to z axis bars, 8 to attach y axis smooth rods, 4 for 608 bearings, 4 to mount motor | |
| 2 | Prusa Bar Clamp | Attaches lower middle rod to bottom left and right frame rods | |
| 4 | Prusa Frame Vertex with Foot | Bottom connectors and feet for the Prusa frame, 1 in each lower corner | |
| 2 | Prusa Frame Vertex | Top connectors for Prusa frame, 1 top left, 1 top right | |
| 4 | M8 x 30mm Fender Washer | Keeps y-axis belt from falling off bearing, 2 front, 2 back | |
| 2 | 608 Bearing | Idler for the y-axis belt, 1 front, 1 rear | |
| 6 | M8 x 370mm Threaded Rod | Forms side triangles of the Prusa frame, 3 per side | |
| 4 | M8 x 294mm Threaded Rod | Connects side frame triangles, 2 bottom front, 2 bottom back | |
| 3 | M8 x 440mm Threaded Rod | Connects side frame triangles with extra length to attach z-axis, 2 top, 1 bottom middle | |
| Hot end | |||
| 1 | Makergear Hotend | Heats filament, extrudes filament through nozzle onto heated bed | |
Purchase Info
Vendor Name
Vendor Item Name or ID
Vendor Item URL
Price per Item
# to Buy for Entire Project